صيانة الحاسوب حسب برنامج A+

PC Installation, Configuration and Upgrading

 

 

القسم الاول

القسم الثاني

القسم الثالث

القسم الرابع

القسم الخامس

القسم السادس

 

 

Part3

اجهزة سكازي

SCSI Devices

 

Small Computer Systems Interface (SCSI) is a complete additional expansion bus (sub-bus) used by PCs, Macintoshes, and UNIX systems to attach and add peripheral devices.

يمكن انتقال المعلومات بين الا جهزة بدون تدخل المعالج

جميع اجهزة سكازي تعمل مستقلة عن المعالج وعن بعضها البعض عن طريق بطاقة سكازي – تكون داخل الحاسوب  PCI

 

SCSI devices can exchange data between them without the intervention or attention of the CPU. All devices on the SCSI bus (chain) function independently, under the control of the host adapter (usually ISA or PCI interface card).

كل قطعة سكازي في الحاسوب لها رقم تعريف خاص

All SCSI devices must have a unique ID, and the SCSI chain must be terminated at both ends.

SCSI Types

انواع سكازي

Interface

Bus
Speed

Bus
Width

Transfer
Rate

Cable
Length

Max
Devices

Regular SCSI-1

5 MHz

8 bits

5 MB/s

6 m

8

Wide SCSI-2

5 MHz

16 bits

10 MB/s

6 m

16

Fast SCSI-2

10 MHz

8 bits

10 MB/s

3 m

8

Fast Wide SCSI-2

10 MHz

16 bits

20 MB/s

3 m

16

FireWire (serial)

400 MHz

1 bit

400 Mbps

4.5 m

63

Note how SCSI bus width and number of devices match.

 

The Standard for serial SCSI bus, aka FireWire, is IEEE1394

Install and configure SCSI devices

كيفية تركيب بطاقة واجهزة سكازي

اجهزة سكازي ممكن ان تكون داخل الحاسوب او خارجه

القطع داخل الحاسوب تكون مربوطة بكيبل واحد وتحتاج كهرباء من الحاسوب بعكس القطع الخارجية.

SCSI devices can be internal, external or a combination, so there are many configurations possible. Internal devices are connected with a single ribbon cable, and require a PSU connection. External devices are daisy-chained, and have their own power connection.

 

All SCSI devices require a unique ID, as this is how the host adapter identifies the devices and identifies priority in the chain. The higher the number, the higher the priority. The host adapter is usually set to 7. Hard drives are usually set to 0.

كل قطعة سكازي لها رقم تعريف خاص وكلما كان الرقم اعلى كلما كان له اولوية اكثر.

 

The chain requires termination at both ends (Only SCSI-1 requires manual termination; later specs are self-terminating).

Installation

تركيبه

1.      Install the SCSI host adapter, ensuring no conflicts

قم بتركيب البطاقة (سكازي) اولا

2.      Install internal devices and/or daisy chain external devices, ensuring all cable and power connections are correct.
قم بتركيب قطع سكازي الداخلية  اولا وتاكد من عدم وجود تضارب بين ارقام التعاريف للسكازي

3.      Set/check SCSI Ids (0-7) – jumpers on SCSI hard drives, buttons (some are plug n play)

يتم اخذ الارقام للسكازي تلقائيا (للاجهزة الجديدة) والا يلزمك الدخول على اعدادات السكازي  (تكون قبل اعدادات) السيموس.

4.      Check termination
للاجهزة القديمة يلزم (تسكيرة)  لاغلاق الفتحة للجهاز الاخير في السلسلة.

5.      Install SCSI drivers
تركيب البرامج والتعاريف لكل قطعة سكازي

PC Disassembly/Assembly

ماذا نفعل قبل تجزئة الحاسوب (قبل فكّه):

Before disassembling a computer, always:

bullet

Backup everything important
قم بعمل نسخ احتياطية من جميع البرامج والملفات قبل البدء

bullet

Have a clean workspace with all the necessary tools and equipment

تاكد من وجود منطقة نظيفة وفارغة والادوات الضرورية

bullet

Take ESD precautions

احذر من الكهرباء الساكنة

bullet

Document everything

قم بتوثيق ما تعمل

bullet

Power off all devices and disconnect them from the mains power supply

قم بفصل  الكهرباء  عن جميع القطع الداخلية والخارجية

bullet

Take your time

 

خذ وقتك

Typical Disassembly:

خطوات فك حاسوب:

1.      Detach keyboard and mouse from back of computer
فك لوحة المفاتيح والماوس

2.      Detach monitor
فك الشاشة


 

3.      Detach serial and parallel devices
فك القطع التسلسلية والطابعات

4.      Detach network cables, speaker cables, joystick, modem phone line...

فك كيبل الشبكة والسماعات والمودم

5.      Detach power cable
فك كيبل الكهرباء

6.      Remove system case lid
فك ازرار الاضاءة

 

7.      Detach internal power cables from storage devices
فك كوابل الكهراء للقطع الداخلية

8.      Remove hard drive and other storage devices
فك الاقراص الصلبة

9.      Remove interface cards
فك البطاقات

10. Remove power cables from system board (removing PSU is not part of the disassembly)
فك كوابل الكهرباء من اللوحة الام

11. Remove CPU
فك المعالج

12. Remove RAM
فك الذاكرة

13. Remove all cables from system board
فك الكوابل من اللوحة الام

14. Remove screws/clips holding system board in place
فك البراغي من اللوحة الام

15. Remove system board (if replacing system board; otherwise it is not necessary for disassembly)
فك اللوحة الام اذا لزم الامر

Reassembly

اعادة التركيب

Reassembly in the reverse order, noting:
نقوم بالخطوات السابقة بالعكس مع ملاحظة ما يلي:

bullet

Proper cable orientation (and all cables are re-connected)

تاكد من توصيلة كيبل المعلومات لكل قطعة  (اللون الاحمر يكون رقم 1)

bullet

CPU orientation (pin 1)

تاكد من وضعية المعالج

bullet

Jumper settings

تاكد من وضعية الجمبرات 

bullet

System board is well-secured in place

تاكد من ان اللوحة الام ثابتة بشكل جيد في مكانها

bullet

Everything you documented as you went along is back in its place

كل ما وثقته سابقا  قم بعمله بشكل عكسي

PC Tool kit

ادوات العمل

bullet

Screwdrivers (TORX, Hex, Phillips)

مفكات

bullet

Tweezers, grips

زرديات

bullet

Chip remover (DIP, EEPROM removal tool)

اداة لخلع التشيبات

bullet

Container (for screws, blanking plates)

حاوية للبراغي

bullet

Flashlight (a penlight is great)
مصباح

bullet

Magnifying glass

عدسة تكبير

bullet

Compressed air can, or natural bristle brush (or PC vacuum)

علبة هواء مضغوط

bullet

Multimeter

مولتيميتر

bullet

ESD kit

توصيلة التفريغ للكهرباء الساكنة

BIOS and the Boot process

BIOS (Basic Input/Output System) chips

انواع البيوس

bullet

EPROM: Erasable Programmable ROMs - flashed with UV light

قطعة التشيب المبرمجة كهربائيا

bullet

EEPROM: Electrically Erasable Programmable ROM – flashed in situ, upgrades downloaded off vendor website usually.

قطعة التشيب المبرمجة كهربائي وتبرمج مرات عديدة كهربائيا

bullet

BIOS is loaded into the top 64 K of the first MB of system memory

معلومات البيوس موجودة في اول 64 كبلوبايت من الذاكرة المؤقتة

bullet

CMOS settings kept in volatile RAM (requires a battery)

معلومات السيموس تكون موجودة في ذاكرة مؤقتة ولذلك تحتاج الى بطارية مثل معلومات التاريخ للحاسوب والوقت

 

BIOS/CMOS Setup

BIOS/CMOS (Complimentary Metal Oxide Semiconductor) setup stores:

bullet

Date, time, and daylight savings

الوقت وتاريخ الحاسوب

bullet

IDE primary and secondary master/slave parameters

مواصفات القرص الصلب والسي دي روم

bullet

Floppy disk type

نوع جهاز الاقراص المرنة

bullet

Video display type

نوع بطاقة الشاشة

bullet

Halting POST error types

طريقة اصدار التصفير عند وجود مشاكل

 

Internal (L1) and external (L2) cache

معلومات ذاكرة الكاش

bullet

Boot sequence and power-on/boot delay

ترتيب الاجهزة واولوياتها عند بدء التشغيل

bullet

NumLock status

وضع هذا الزر عن التشغيل (مضاء او مطفأ)

bullet

Keyboard installed (optional POST halt)

تركيب لوحة المفاتيح

bullet

nnnnn-nnnnn shadow

bullet

Shadow RAM

الذاكرة

bullet

Video and System BIOS shadows

ذاكرة بطاقة الشاشة

bullet

Integrated FDC (Floppy Disk Controller)

تحكم جهاز الاقراص المرنة

bullet

Integrated IDE Controllers

تحكم جهاز الاقراص الصلبة

bullet

Integrated serial ports

تحكم التسلسلي

bullet

Integrated parallel ports (EPP, ECP

تحكم الطابعة

bullet

PS/2 port enable
تحكم

bullet

USB enabled

تحكم

 

Note: Run through the CMOS setup program on your computer to become familiar with it.

IRQs, DMAs, IO addresses

 

All of these can be checked in the Windows Device Manager or Microsoft Diagnostics (MSD) on your computer.

IRQ (Interrupt Requests)

The processor performs one task at a time, even if it seems simultaneous. To switch between multiple tasks, a processor shares its time by:

bullet

Polling: processor checks each task in turn if it needs attention (waste of CPU time)

bullet

Interrupting: each task tells the processor when it needs attention with one of two PICs (Programmable Interrupt Controllers) on the system board (IRQ 0-7 is PIC 1; IRQ 8-15 is PIC 2)

 

bullet

NMI: Non-Maskable Interrupts are urgent interrupt requests that the processor cannot ignore (like memory parity check error)

bullet

Devices can share interrupts if they are not used at the same time.

bullet

PCI Interrupts: the PCI bus has its own interrupt system (#1-#4 or #A-#D) handled by the PCI BIOS

 

 

0

System Timer

1

Keyboard

2(9)

Video Card or cascade to IRQ 9

3

Com2, Com4

4

Com1, Com3

5

Available (Normally sound card or LPT2)

6

Floppy Disk Controller

7

Parallel Port (LPT1)

8

Real-time clock

9 (2)

Redirected IRQ2

10

Available

11

Available

12

PS/2 Mouse

13

Math Coprocessor

14

Hard Disk Controller (HDC)

15

Available (often used for second HDC)

 

  

العودة لصفحة الصيانة

Home

Send mail to webmaster@matcom.netwith questions or comments about this web site.
Last modified: 10/07/ 2004